How to fix

Bathtub Faucet Won’t Turn Off: 2 Main Causes & How To Fix

The majority of people have experienced bathroom faucets that won’t turn on or don’t have the water pressure they prefer, so it may be rather shocking when you go to turn off the faucet and the water just keeps running. Even while it appears like you should always be able to turn things off, there are specific circumstances that really make it impossible for the faucet to turn off properly.

It could be time to look for local home and business plumbing services if you’re experiencing one of these problems. You might not be able to turn off the water in your bathroom for the following reasons.

When the bathtub water continues to stream even after ten attempts to turn off the faucet, a correction needs to be made right away. You must be aware of the issue preventing the bathtub faucet won’t turn off in order to solve it.

Causes of the Bathtub Faucet won’t turn off

The following are the primary two causes of the bathtub’s ongoing water problem:

A faucet handle with damage

A broken handle could make it difficult for you to turn off the water faucet in your bathtub, albeit that is not the main cause. A stem can be seen inside the handle. After passing through it, the water empties into the bathtub where you can have a soothing bath.

But occasionally the handle could break. The stem could also sustain injury. In both scenarios, the stem won’t have enough grip, causing the water to flow through it continuously. You have to swap out the handle when that happens.

Single or double handles are available for the bathtub faucet. Standard and simple to replace faucets are those with two handles. The modern bathtub handles, on the other hand, could be a little more difficult to take off and put back on.

A corroded or damaged valve

The faucet’s internal valve regulates how much water flows through the stem. The valve’s capacity to regulate the water flow to the sprout is lost when it completely or partially wears out. You need to repair the valve when it becomes damaged as a result of its extended usability.

Of course, you may give it a shot with a DIY project. However, not everyone may be able to DIY replace a damaged valve. So, you may speak with a qualified plumber.

How To Fix

Now that we are aware of the key causes, we can fix the problem. So it’s time to solve the issues and stop worrying.

Method 1: Squeezing the faucet handle

If the handle comes free, the stem is broken, or the valve of the sprout is damaged, the bathtub faucet might not shut off. The simplest approach, though, is to tighten the loose handle; it works almost 80% of the time.

  • A flathead screwdriver is required. With the screwdriver, pry the faucet cover plate off.
  • The screw can be found when you remove the cover. Using the screwdriver or an adjustable wrench, begin tightening it.
  • After that, try closing the water faucet and evaluate the outcome. You should typically be able to turn off the bathtub faucet.
  • Even so, sometimes turning the water faucet handle tighter won’t help. It implies that the issue is significant and that you must put in a lot of effort.

Method 2: : Try Replacing the Bathtub Faucet Stem

The damaged stem inside the handle has to be repaired or replaced if tightening the faucet handle does not stop the flow of water. Given how challenging the work is, you must adequately prepare.

However, keep in mind that replacing the stem inside the bathtub faucet handle is only a short-term repair if the water won’t turn off completely. It will only endure for a few months before needing a complete stem replacement.

Step 1: Cut the stem off

First, shut off the bathtub faucet’s main water supply. It will prevent any unintentional spills and restroom flooding. It also enables you to operate efficiently without making a mess. The faucet handle on its right should then be turned and pulled out to uncover the stem.

Use a tool to pry the stem off if you don’t want to take the chance of harming your hand. Move the wrench while attached to the handle until the stem is correctly removed.

Step 2: Examining the Stem

Now, closely inspect the stem to see if it has any flaws or damage. There will be ridges or rims on the stem’s tip. It joins the handle’s interior ridge. Long-term use will cause the ridge to deteriorate and lose its ability to tighten through the stem when you shut off the water supply.

As a result, the faucet won’t shut off, and water will drop into the bathtub as a result. Therefore, it would be better to replace the faucet handle’s ridge or the entire stem.

Step 3: Clean the stem

On occasion, waste deposits and debris may collect in the stem. The stem will get damaged or loosened. For the stem to function correctly once again, you must remove these deposits.

You may use any toothbrush for this with ease. Brush the stem thoroughly, being sure to get rid of all the debris. The cleaning task might need to be done several times.

Step 4: Thread Tape Wrapping the Stem

You must wrap thread-seal tape around the damaged stem to temporarily repair it. At the very least, use thread tape to wrap the valve stem tip twice. The faucet handle should then be pressed all the way through the stem that has been wrapped in thread tape.

Be careful that the handle does not slide off the thread tape and covers the threaded stem properly. You can carefully turn the handle over the stem until it reaches the end and precisely locks for safety. Additionally, it is easier to complete with a wrench and requires less force.

Step 5: Concluding the Work

Check to see if the water stops flowing when you reinstall the handle on the bathtub faucet. It ought to work in most situations. However, it is only a short-term fix, so you must get ready to replace it as soon as possible, ideally within a few months, with a new faucet handle.

Method 3: Fix the bathtub faucet using

The bathtub faucet must be fixed if none of the two procedures we stated above work to stop the water dripping. Fortunately, it is possible to repair a broken or troublesome bathtub faucet yourself, without the assistance of a professional.

We advise you to put on gloves and safety eyewear before you begin repairing the bathtub faucet. You will be shielded from all possible dangers.

In order to prevent any bathroom flooding, shut off the main water supply. To do this, close the valve and begin your task. Your basement or garage should contain the primary supply line valve.

Your smartphone camera will be useful at this point. Take a couple pictures of the faucet with the camera. Take a few pictures of the handle as well. You could buy the necessary components more quickly if you had these photographs. If necessary, you can also provide the images to help the plumber understand the issue better.

Start working on fixing the faucet once you have all the necessary components. First, use a flathead screwdriver to pull off the faucet handle. Then, you should get to the screw that is hidden beneath the faucet’s attractive cover.

With the adjustable wrench, locate the packing nut and loosen it before removing the faucet stem. Use the wrench to remove the stem if you are unable to pry it off with your hands. The stem won’t need to be replaced if it is in good shape. (If fixation is required, use our Method Two.)

Most of the time, a damaged faucet washer causes the bathtub faucet to run continuously. Therefore, you need to replace the valve’s washer and O-ring with new ones. For your faucet to function properly, make sure that the O-ring and washer are the same size. Otherwise, your investment will be in vain.

Reassembling the water faucet is necessary after replacing the O-ring and washer. Be careful not to harm the stem or handle while doing this. Make sure not to damage or appear unattractive while prying off the decorative top.

In order to turn off the bathtub water faucet, first turn on your main water supply. If the bathtub continues to fill up, we advise calling a plumber to handle the situation and repair or replace the entire faucet.

Shower Upkeep Advice

You will undoubtedly run into issues with your shower, it is a fact. But more crucially, the showerhead itself can serve as a haven for many microorganisms.

As a result, it’s crucial to maintain your shower so that it’s functional, safe, and clean. Try to be gentle with the grout when cleaning your shower and its faucet.

Use soft cleaners like baby shampoo and water as an alternative to harsh ones. Start by dipping a soft nylon brush into the solution.

Check your home’s water pressure if you discover that the water flow is weak. Check your showerhead for any accumulation if the other faucets are operating normally.

Invest in calcium and lime solution to clear any buildup that might be preventing the spray jets from working properly. A showerhead with rubber-tip jets is the way to go if you want to enhance your bathroom. With a quick wipe with a cloth, this is simple to clean.

Last Words

Everyone enjoys taking a relaxing bath in the bathtub. However, the experience can be horrifying and unpleasant if the bathtub faucet won’t shut off after batting. Fortunately, there are three simple solutions to the issue.

First, try tightening the handle to see if it fixes the problem. Check the stem inside the handle and mend it with the thread-seal tape if it breaks. Finally, to stop the water from the bathtub, fix or replace the entire faucet system. Consult a plumber if none of these three techniques work to halt the water flow. See more useful articles in our website Foto Blog Diario.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button